Accessories.
Everything around the charger
One range covers what holds the charger, what measures the connection and what keeps the cable off the ground.
Mounting
One universal pole platform for One, One Business and Two Pro. Install the foundation once; when the charger changes, only the bracket changes.
Metering
P1 and Modbus meters that feed load balancing and solar charging in Plugchoice, from the plug-and-play Sparky to the Flint gateway.
Cables & Holders
Charging cables and the cable holder keep the connector off the ground and the cable in one place, on the pole or on the wall.
One pole, every Volt Time charger
Install the infrastructure once. The foundation and pole stay; a charger-specific bracket is the only part that changes when you swap or upgrade. From private driveways to larger commercial charging locations.
See parking solutions
From bracket to roof
Both poles start the same way: the ground anchor bolts down, the brackets bolt tight, the charger lands on its plate, and the cable holder clips underneath. Only the Pro takes the connection kit inside: hatch open, kit in, hatch closed.
The Pro's rear face is the flexible one. A second charger mounts there, or a 2x 16A socket outlet takes the same holes. A light and a roof finish the top, and the light comes on at dusk.
Wired inside the pole
The 3P+N+PE connection kit clicks into the service compartment: three phases, neutral and earth as five pluggable modules. The access panel closes over them, and the pole face stays clean.
Installers reach everything from the front. No dismounting the charger, no opening the charger housing.
Any charger, same two bolts
The swap in real time: bolts out, plate off, the next plate onto the same holes, bolts back in. Each charger brings the adapter plate sized for it; the pole face never changes.
Change the charger without touching the pole or its foundation.
Swap the charger, keep the pole
The charger is not structurally part of the pole. Dedicated brackets for One, One Business and Two Pro attach to the same platform, so a future upgrade never becomes a groundworks project.
LITE and PRO poles
LITE 1200 is the slim single-charger pole for homes and private parking. PRO carries single or double configurations, has an integrated access panel and rotates 180 degrees for ceiling-mounted, low-clearance parking.
No concrete needed
The Universal Mounting Base is a flat-packed foundation with click-and-bend assembly in one to two minutes, using just an adjustable spanner. Adjustable feet handle sand, clay, compact ground and narrow cable trenches.
Built for coastal weather
Powder-coated, seawater-resistant aluminium with an ISO 12944 category C4 coating system, in RAL 9005 black as standard. Other RAL colours are available for projects.
Ready for rows
The PRO connection kit distributes one incoming feed across as many as four charger outputs and daisy-chains poles, rated up to 100A and 450V.
Low-carbon aluminium
The PRO line is built with Hydro CIRCAL recycled aluminium, roughly 75% of the documented assembly, and is designed for a minimum service life of 20 years.
The wider mounting-pedestal platform has undergone independent third-party safety testing by TUV Rheinland. For projects, the platform also supports options like integrated lighting, protective roofs, safety bollards, signage and payment-terminal mounts.
The mounting range
Four building blocks: two poles, one foundation, and the charger-specific brackets that tie them to the charger.
Universal Mounting Pole, Lite
Universal Mounting Pole, Pro
Universal Mounting Base
Brackets & Connection Kit
Metering that feeds the smart charging
Load balancing, solar charging and peak shaving in Plugchoice start with a meter that sees the connection. Sparky reads the P1 port in about a minute; Flint adds Modbus and control for bigger sites.
Learn about smart charging
Sparky, plug and play
Slides into the smart meter's P1 port and is online in about a minute, with data down to the second and a built-in P1 splitter for a second device. Works with the Dutch smart meters known to Chargee.
Flint, the gateway
Reads and controls energy assets over Modbus, M-Bus, RS232 and digital I/O, with Ethernet and Wi-Fi standard and 4G optional. P1 in and out, and it can dim or pause solar inverters to limit feed-in.
In-line and CT options
Eastron in-line and CT meters and the Xemex CSP1+ cover larger connections, combined with a Flint or Sparky as the bridge to Plugchoice.
Security in order
Chargee is ISO 27001-certified for information security, independently assessed by Kiwa Nederland. Traffic is encrypted with 128-bit AES over TLS/SSL, Wi-Fi supports WPA2 and WPA3, and Sparky receives automatic security updates.
Supported meters
| Meter | Type | Connectivity | Notes |
|---|---|---|---|
| Chargee Sparky Confirmed | P1, HAN | WiFi 2.4GHz | (D)SMR4.0+ |
| Chargee Flint Confirmed | Modbus, P1, HAN | Ethernet RJ45, WiFi 2.4GHz, 4G (optional) | Modbus, HAN and P1 (SMR4.0+) |
| Eastron SDM72D-M Confirmed | In-line | Modbus | With Flint or Sparky (Modbus) |
| Eastron SDM630MIDMBUS Supported | In-line | Modbus | With Flint or Sparky (Modbus) |
| Eastron SDM72CTM Supported | CT | Modbus | With Flint or Sparky (Modbus) |
| Xemex CSP1+ Confirmed | CT | P1 | With Flint or Sparky (P1) |
The cable off the ground
The cable holder stores the charging cable and connector in one place, on the PRO pole with its mounting bracket or straight on a wall. Add a portable charging cable and the daily routine stays tidy.
Cable and connector holder
One housing for the coiled cable and the connector, keeping both off the ground. Powder-coated, seawater-resistant aluminium outside, recycled plastic inside.
On the pole or on the wall
The cable holder mounting bracket positions it beneath the charger on the PRO pole, supplied with 316L stainless-steel screws. Without a pole, it mounts independently, commonly on a wall.
Portable charging cables
Type 2 charging cables for the socket versions of our chargers, so one cable in the trunk covers home, work and public charging.
Same finish as the range
RAL 9005 black with the same ISO 12944 category C4 surface treatment as the poles, so mixed installations keep one visual language.
Common questions
Mounting, foundations and meters.
Which chargers fit the mounting poles?
Dedicated brackets. Volt Time supplies standard mounting brackets for One, One Business and Two Pro. The bracket is the interface: the pole and foundation stay universal.
Other chargers. The wider platform can accommodate other chargers through separately engineered brackets, but those are custom, project-specific solutions.
Do I need to pour concrete?
Usually not. The Universal Mounting Base is a flat-packed in-ground foundation with click-and-bend assembly in about one to two minutes, needing only an adjustable spanner.
Levelling. Adjustable feet handle sand, clay, compact ground, light soil and narrow cable trenches, and the bolt height lets you level the pole precisely.
Which meter do I need for load balancing?
Homes. Sparky slides into the smart meter's P1 port and is online in about a minute, with data down to the second for dynamic load balancing.
Bigger connections. Flint adds Modbus and control. Eastron in-line and CT meters and the Xemex CSP1+ combine with a Flint or Sparky as the bridge to Plugchoice.
Can the pole hang from a ceiling?
Pro. The PRO pole can be rotated 180 degrees for ceiling-mounted applications such as low-clearance parking environments.
Lite. The LITE footplate supports floor or ceiling installation where the project permits it.
Finish the installation
Get a quote for poles, meters and holders together with your chargers, or talk to our team about a project configuration.